PRODUCTS CENTER

pressure rubber hose specication

GENERAL PURPOSE FLEXIBLE HOSES

※Flexible hoses for high pressure and ultrahigh pressure can be specially designed. ※The specifiions are subject to change for product improvement without prior notice. ※The maximum working pressure may vary depending on the design conditions. ※1: Pressure at working temperature of 40°C, safety factor of 3 and weld efficiency of 0.7 Nominal diameter …

SAE 100R2 High pressure, steel wire reinforced, rubber

Type A - Thick cover (skive type) Type AT - Thin cover (no-skive type) Construction: This hose consists of an inner tube of oil synthetic rubber, two wires braid reinforcement, and an oil and weather resistant synthetic rubber cover. Tube: Oil resistant synthetic rubber. Reinforcement: two high tensile steel wire layers 2/w Cover: Abrasion and weather resistant synthetic rubber

HEBEI QIANLI RUBBER PRODUCTS CO., LTD. - High …

High Pressure Rubber Hose back to contents Size SAE Size I.D Reinforcement W.D O.D Max W.P Proof Pressure P.P Min B.P Min B.R Weight A AT mm inch dash min max min max min max max MPa Psi MPa Psi MPa Psi mm kg/m 5 3/16 -3 4.6 5.4 10.6 11.7 15.1 16.7 14.1 35 5075 70 10150 140 20300 90 0.32 6.3 1/4 -4 6.2 7 12.1 13.3 16.7 18.3 15.7 35 5075 70 10150 140 …

Technical TECHNICAL

Hose Flow Capacities Pressure Drop Pressure drop in psi (pounds per square inch) per 10 feet of hose (smooth bore) without fittings. Fluid specifiion: Specific gravity = 0.85; Viscosity = v = 20 centistokes (C.S.), (20 C.S. = 97 S.S.U.) Pressure drop values listed are typical of many petroleum based hydraulic oils at approximately +100ºF

ISO - ISO 6804:2009 - Rubber and plastics inlet hoses and

ISO 6804:2009 specifies the requirements for three types of rubber or plastics inlet hoses and hose asselies for washing-machines and dishwashers connected to the domestic water supply at a pressure not exceeding 1 MPa (10 bar). It is applicable to the following types of hose:

High Pressure Hydraulic Hose R4 with Synthetic rubber cover

Home > Products > Rubber Hoses > High Pressure Hydraulic Hoses > R4 High Pressure Hydraulic Hoses. R4 High Pressure Hydraulic Hoses gayatri 2021-08-13T12:51:44+00:00. R4 High Pressure Hydraulic Hoses. SAE – 100 R4 Specifiions. Confirming to std. SAE – 100 R4. Construction. Tube: Seamless oil resistant. Reinforcement: Consisting of braided textile …

FRAS Suction Hose | Hoses | Pacific Hoseflex

25/6/2015· Metallic Hose. Stainless Steel Hoses – Our Vitalflex® stainless steel braided hose asselies are the most superior range of flexible metal hoses on the global market. Vitalflex® Asselies can be made in 304, 316 and exotic materials such as Monel. These asselies can be certified to AGA and WaterMark standards as well as welding to AS 4041 and ASME IX …

Hose Specs | Precision Hose Technology

APPLIION: Low pressure air and vacuum instrument systems. Vacuum service 20 Hg sizes -2 thru -6; 10 Hg sizes -8 and -10. TEMPERATURE RANGE: -65°F to 165°F (-54°C TO +74°C) EQUIVALENT P/N: Aeroquip 306. NOTE: Beech, Cessna and Piper used this hose for fuel, oil and hydraulic drains.

Fuel Hose Selection, Pipe Grading (Why R9), Connections

Low Pressure Synthetic Rubber Hose: 200 g/m²/day: 50 PSI: Inner Resistant To Petrol, Diesel, Oil Or Vapours Ozone & Heat Resistant Outer: R9: Fuel Injection Synthetic Rubber Hose: 15 g/m²/day: 100 PSI: Inner Resistant To Chemical Attack, Swelling, And Permeation By Gasoline, Oxidized ("Sour") Gasoline, Ethanol Extended Gasoline, Diesel Fuel, And Oil Or Lubricants Or …

Flexible Hose Product Specifiion HIC Manufactured

Flexible Hose Product Specifiion HIC Manufactured UNIVERSAL Brand Universal Flexible Hoses ensures burst-proof hydraulic pneumatic pressure flow, in a way, hose inner lining rubber tube is made of compounded synthetic rubber, braiding material used is either of textile dipped nylon yarn or woven ply cotton fabric and or galvanized iron wire for operating pressure rating …

Hydraulic Hose - Hydraulic Hose R2-1/2 Manufacturer from

Constant Working Pressure Hose part of the globalcore line of robust yet lightweight hydraulic hose, Parker’s 797 hose is an easy-to-blend, easier-to-install 6000 PSI constant working pressure hose. Parker’s 797 hose, within the globalcore product line, was designed to deliver consistency and reliability with a constant working pressure of 6,000 PSI in all sizes.

Hydraulic Hoses - RYCO Hydraulics

We offer many different hose types and pressure ranges to suit a wide variety of appliions. No matter your pressure system’s needs, RYCO has you covered. RYCO Range. The RYCO range consists of our premium ISOBARIC Braid, ISOBARIC Spiral Hoses, Traditional Braid, Spiral Hoses, Speciality and High Temperature, Water Blast and Pressure Washer, Suction and …

Industrial Hose Selection Guide: Types, Features

SPECIFIIONS Recommended for: High pressure hydraulic oil lines. Meets or exceeds requirements of SAE 100R2A. Tube: Black, oil resistant, Nitrile (NBR). Reinforcement: Two braids of high tensile steel wire. Cover: Black, oil and abrasion resistant Neoprene (CR). MSHA accepted. Temperature range:-40°F to +250°F. Min. Wt. Hose Hose Rated Min

SAE 100R1 Wire Braided Medium Pressure Hose with Two Options

SAE 100R1 high tensile steel wire braided medium pressure hose. SAE 100R1AT single steel wire braided hose is a typical medium pressure hydraulic hose and strongly recommended for hydraulic lines or general industrial system. High tensile strength steel wire reinforcement makes SAE 100R1 hose support higher pressure than common steel wire does.

Linatex Rubber Products - Weir Group

Linatex® Hard Wall Slurry Hose (808) Technical Specifiions The Linatex® 808 hard wall slurry hose range is custom built and designed to deliver outstanding wear performance in the most arduous of mining and industrial appliions. Our world renowned wear resistant rubber compounds complement our hose range and offer our clients the lowest cost of ownership. …

ISO - 23.040.70 - Hoses and hose asselies

183 rows· 23.040.70. Rubber and plastics hoses and hose asselies — Methods of …

Rubber Hose - High Pressure Hydraculic Hose R1 Manufacturers

SAE – 100 R1 / EN 853 1SN/ DIN 20022 1SN Specifiions. Conforming to Std. SAE – 100 R1. Construction

High Pressure Hydraulic Hose, 1SN, 2SN, 4SP, 4SH, R13 and R15

We can supply standard high pressure hydraulic hose including high-pressure hose EN 853 1SN, 2SN, 4SP, 4SH, SAE 100R13 and R15. They are used as flexible hoses in the hydraulic systems of machines and mechanisms for the transportation of mineral and hydraulic oil, fuel oil and water-oil emulsions.

Hose Shop | Hoses - Our Products

Petrol-Resistant Rubber Hose. Chem. Chart • Temp/Pressure. 90deg Rubber Bend. Chem. Chart • Temp/Pressure. Silicone Heater Hose. 10mm - 25mm. Chem. Chart • Temp/Pressure. Composite & Stainless Steel. WAM Fuel/Oil SD 1000. WP: 10bar • 25mm − 150mm. Chem. Chart • Temp/Pressure. WAM Fuel/Oil HD 901. WP: 15bar • 25mm − 150mm. Chem. Chart • …

ESR 0405 - Specifiion for rubber hose

Specifiion for rubber hose ESR 0405 Document control Revision Date Summary of change (RSS 0405) 1.0 August 2007 Based on TRS 0007 (ESR 0405) 1.0 June 2010 Reformatted and renuered ESR 0405 Summary of changes from previous version Summary of change Section NOTE – If the final document is small enough for the ‘Contents’ and ‘Document control’ to fit …

TECHNICAL SPECIFIIONS - Green Line Hose & Fittings

exhibit rubber-like features, and vice-versa. Hose selection will depend on the characteristics of the particu-lar elastomer formula that best fit the appliion. Technical 163 TECHNICAL SPECIFIIONS Pressure: 1 psi = 2.307 ft of head (ft of water column) = 2.036Hg = 0.06895 Bar = 0.006895 MPa (MegaPascals) = 0.07031 Kg/sq cm = 0.06805 Atmospheres 1 Bar = …

Rubber Composite Hose Ducting - Fluid Transfer & Hose

116 Rubber Hose - Industrial RUBBER, COMPOSITE HOSE & DUCTING RUBBER,COMPOSITE HOSE & DUCTING 1 2 3 4 5 6 7 4.02 8 Part Nuer Nominal Dia. Working Pressure Weight

High Pressure Rubber Hose Wire Type Technical

Flexible Hose Product Specifiion HIC Manufactured UNIVERSAL Brand. Universal Flexible Hoses ensures burst-proof hydraulic pneumatic pressure flow, in a way, hose inner lining rubber tube is made of compounded synthetic rubber, braiding material used is either of textile dipped nylon yarn or woven ply cotton fabric and or galvanized iron wire for operating pressure rating …

Indian Standard: High Pressure Fire Fighting Hose

HIGH PRESSURE FIRE FIGHTING HOSE— SPECIFIION. 1 SCOPE. This standard lays down the requirements of high pressure fire hose. 2 REFERENCES . The Indian Standards listed below contain provisions which, through reference in this text, constitute provisions of this standard. At the time of publiion, the editions indied were valid. All standards are subject …

Hose Assely & Testing - Belt and Hose

Adelaide Belt and Hose are able to professionally select and build hose asselies to meet your specifiions or exacting appliions. All hose asselies are proof tested and tagged to the highest standards, for your quality satisfaction and safety considerations. NATA endorsed testing laboratory with scope to conduct static and hydrostatic pressure testing of hose asselies, …

SAE Hydraulic Hose – Ideal for Low, Medium and High

SAE 100R3 double fiber braid hydraulic rubber hose is ideal for medium pressure fuel and oil lines as well as return and suction hoses of hydraulic systems. It is constructed with an inner tube of oil-resistant synthetic rubber, a reinforcement consisting of a ply, or plies, of woven or braided textile fibers with a suitable spiral of body wire, and an oil and weather resistant synthetic

SVAROG uses SIKORA measuring device for rubber high

26/11/2021· Quality requirements of rubber high-pressure hoses are very high and determined by standards. Therefore, since 2007, when the plant started its operation, SVAROG has been focusing on manufacturing high-pressure hoses in accordance with the European standard DIN EN. The product range of SVAROG includes different types of rubber hoses with an outer …

Rubber Mining Hose | Linatex Hard Wall | Weir

The Linatex® Hard Wall Mining Hose is designed to the highest engineering standard. Custom designed hoses specific to the customers needs available. Design ratings. Each hose is manufactured with a 3:1 safety factor for working pressure. Size range/-dimensions. Sizes range from 2" to 72" ID and hose lengths to 50 ft. Pressure class/-power rating

SAE 100 R1 Steel Wire Reinforced - High pressure hose

It can bear higher working pressure than other rubber hoses thanks to its high tensile braided steel wire reinforcement. It is composed of three parts: tube, reinforcement and cover. The tube is made from oil resistant synthetic rubber, making the hose have excellent performance in delivering oils. The reinforcement is made from one layer of high tensile braided steel wire, …

Hose Specifiions - Aeroflow Performance

Compatible Hose Ends: 100, 150, 500, 550 and 880 Series reusable Hose Ends. 400 SERIES HOSE • Easy to assele with reusable push lock hose ends • Clamps must be used for all pressure appliions. • Smooth bore Chlorinated Polyethylene (CPE) synthetic rubber inner liner • Available nylon reinforced blue or black outer cover